Savanoriu 65A, Vilnius, Lithuania +370 (5) 210 22 74 info@tekknow.lt
    Flaw Detector
  • Sizing Toolkits: DAC, AWS, TCG, DGS
  • Exception visibility in sunlight (AMOLED) color VGA display (320×240 pixels)
  • P.R.F. – 8 to 333 Hz, adjustable
  • Screen Refresh Rate: Adjustable 60 & 120
  • Detection: Z-Cross, Flank & Peak
    Thickness Gauge
  • Automatic: probe zero, probe recognition, and Temperature compensation
  • Measurement: Variety of modes to address a number of applications
  • Large data storage with multiple formats: Alpha numeric grid and sequential w/auto identifier
  • Windows PC & MAC OSX interface software
  • 2 year limited warranty

Specifications

General

  • Size: 2.5W x .5H x 1.24D in (63.5 x 165 x 31.5mm).
  • Weight: 14 ounces (.397kgs), with batteries.
  • Case: Extruded aluminum body with nickel plated aluminum end caps (gasket sealed).
  • Display: 1/4 VGA AMOLED color display (320 x 240 pixels). Viewable area 1.7 x 2.27 in (43.2 x 57.6 mm). 16 color pallete, multiple color options, and variable brightness.
  • Screen Refresh Rate: Selectable 60 or 120Hz.
  • Display Views: Flaw Detector: Full wave, +/- Rectified, or RF. Thickness Gauge: Digits, +/- Rectified, RF, or B-Scan.
  • Timing: Precision 25MHz TCXO with single shot 100 MHz 8 bit ultra low power digitizer.
  • Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
  • Operating Temperature: 14 to 140F (-10C to 60C).
  • Environmental: Meets IP65 requirements.

Calibration

  • Automatic Calibration: Longitudinal (straight), or Shear (angle).
  • Probe Types: Single Contact, Dual, Delay, and Angle .
  • English (in), Metric (mm), or Time (μs).
  • Velocity: 0.0100 to .6300 in/μs (256–16,000 m/s).
  • Test Range: 0 to 0.280in (7.11mm) minimum, to 1200in (30,480mm) maximum at steel velocity. Continuously variable.
  • Zero Offset (Probe Zero): 0–999.999 μs.
  • Material Velocity Table: Contains longitudinal and shear velocities for a variety of material types.

Pulser

  • Pulser Type: Two adjustable square wave pulsers and receivers.
  • P.R.F.: 8 to 333Hz in selectable steps (8, 16, 32, 66, 125, 250, 333Hz).
  • Pulser Voltage: 200 volt peak amplitude, rise/fall time < 10ns into 50ohm.
  • Pulse Width: 40 to 400 ns. Selectable step options (spike, thin or wide).
Receiver

  • Gain: 0 to 110dB with 0.2dB resolution. Manual and AGC control.
  • Damping: 50, 75, 100, 300, 600, & 1500 ohms.
  • Frequency Bands: DFX-7 & 7+: Broadband 1.8 – 19 MHz (-3dB). DFX-7+: Three narrow bands centered at 2MHz, 5MHz, 10MHz.
  • Horizontal Linearity: +/- 0.4% FSW.
  • Vertical Linearity: +/- 1% FSH.
  • Amplifier Linearity: +/- 1 dB.
  • Amplitude Measurement: 0 to 100% FSH, with 1% resolution.
  • Delay: 0 – 999in (25,375mm) at steel velocity.

Flaw Detector: Features

  • TRIG: Trigonometric display of beam path, depth, surface distance, and curved surface correction. Used with angle beam transducers.
  • DAC: Up to 8 points may be entered and used to digitally draw a DAC curve. Reference -2, -6, -10, (-6/-12), (-6/-14), (-2/-6/-10) dB. Amplitude displayed in %DAC or dB.
  • AWS: Automatic defect sizing in accordance with AWS D1.1 structural welding code.
  • AVG/DGS: Automatic defect sizing using probe data. Stores up to 64 custom setups.
  • TCG: Time corrected gain. 50 dB dynamic range, 20 dB per microsecond, up to 8 points for curve definition.
  • Measurement Mode: Pulse-Echo (P-E) measures from 0.025 in to 100 ft. (0.63mm to 3048 cm).
  • Auto-Cal: Provides automatic calibration with two reference points.
  • Detection Modes: Zero Crossing, Flank and Peak.
  • Display Freeze: Hold current waveform on screen.
  • Peak Memory: For echodynamic pattern determination.

Thickness Gauge: Features

  • Measurement Modes (Dual Element):
  • Pulse-Echo Mode (P-E) – (Pit & Flaw Detection) measures from 0.025 in to 100 ft. (0.63mm to 3048 cm).
  • Pulse-Echo Coating Mode (PECT) – (Material, Coating, Pit & Flaw Detection): Material: 0.025 in to 100 ft. (0.63mm to 3048 cm). Coating: 0.001 to 0.100 inches (0.01 to 2.54 millimeters).
  • Pulse-Echo Temp Comp Mode (PETP) – (Pit & Flaw Detection) Auto temperature compensation – measures from 0.025 in to 100 ft. (0.63 mm to 3048 cm).
  • Echo-Echo Mode (E-E) – (Thru Paint & Coatings) measures from 0.050 to 4.0 inches (1.27 to 102 millimeters). Will vary based on coating.
Features, cont.

  • Echo-Echo Verify (E-EV) – (Thru Paint & Coatings) measures from 0.050 to 1.0 inches (1.27 to 25.4 millimeters). Will vary based on coating.
  • Coating Only Mode (CT) – (Coating Thickness) Measures from 0.0005 to 0.100 inches (0.0127 to 2.54 millimeters). Range will vary +/- depending on the coating.
  • One and two point calibration option for material & coating, or selection of basic material types.
  • Auto probe zero, recognition and temperature compensation.
  • High speed scan up to 50 readings per second.
  • Audible alarm with hi/lo limits.
  • Built-in differential mode for QC inspections.
  • 64 custom setup configurations.

Memory

  • Log Formats: Grid (Alpha Numeric), or Sequential (Auto Identifier).
  • Graphics On: 8,000 readings, A/B Scan image, & all gauge settings for every reading.
  • Graphics Off: 210,000 readings (coating, material, min & max. (Thickness gauge only).
  • Custom Setups: 64 user configurations.

Power Source

  • Battery: Three 1.5V alkaline, 1.2V AA Nicad cells, 1.2V AA NI-MH, or other other equivalent power source. Battery life (continuous use): Alkaline (12hrs), Nicad (5hrs), and NI-MH (12hrs), with default settings.

Connections

  • Output: RS232 serial interface. PC software & USB converter cable included.
  • Transducer Connectors: Two LEMO 00 connectors.

Certification

  • Thickness Gauge: Factory calibration traceable to NIST & MIL-STD-45662A.
  • Flaw Detector: EN12668-1 compliant.

Warranty

  • 2 year limited

If you have any questions about this product feel free to contact with us by email: This email address is being protected from spambots. You need JavaScript enabled to view it. OR phone: +370 (5) 210 22 74.

Do you want to get our newsletters?

By subscribing to our mailing list you will always be update with the latest news from us. We never spam.

JSC "Tek Know Baltic" Lithuania, Vilnius, Savanoriu ave 65A, LT03149

Tel: +370 (5) 210 22 74, Fax: +370 (5) 210 22 75, Email: info@tekknow.lt

© 2016, JSC "Tek Know Baltic". All rights reserved.